GAUS BATTERY CHARGER GBC165V10A
High Frequency Intelligent Multi Step Charger
GBC165V10A (GBC) is microprocessor device for charging and maintenance of starter (or traction) lead-acid batteries in serial connection with voltage range from 10V to 165V and current range from 0A to 10A. It is developed as a consequence of need for small (light), easy for use, safe, reliable, and fully controllable and relatively cheep device for servicing and maintenance of starter (or industrial batteries). It has capacity for simultaneous charge up to 10 twelve volts batteries in serial connection with nominal capacity up to 100Ah. GBC is one-phase high frequency half-bridge constant voltage charger with current limit. That means that current reaches output voltage on connected battery, which is limited. After reaching desired voltage, that voltage level is maintaining constant and charge current drops as battery is charging. GBC is made of two charging modules controlled by main microprocessor. Modules are fitted in common steel box with central control unit, protection devices, and keyboard and display unit. Charge current (current limit) is selected as function of nominal battery capacity, or in function of desired charging time and capacity. Also, charging voltage is settable as charging voltage per one 12V battery (multiplies with number of batteries). Voltage, current, duration and capacity (Ah) are controlled and many precaution measures are implemented.
As device is microprocessor, with measuring current, voltage, duration, Ah, temperature of heat sink of semiconductor parts, it is possible to implement different algorithms. It is possible to change voltage and current limits, conditioning of charge characteristic, pausing, waiting for event (measuring Ah during charge), conditioning end of charging (duration, Ah...), connection with PC computer, analyze and printing charge graphs etc.
Energy circuit is made of input filter with high quality electrolytic capacitors (EPCOS-SIEMENS 105C), high-frequency transformer (ETD Siemens) and mosfet half-bridge (International Rectifier IR), ultra fast diodes, and inductance and PWM modulator. Working frequency is 30kHz.
Thanks to voltage limit, it is possible to charge without surveillance, because there is not over charge (over night or during weekend). As well, in a case of main power failure during charge, after it’s returning device automatically continues charging with parameters, which were previously set (before power failure). LCD display with 2x16 characters shows values of current, voltage, time, capacity, device status, warnings, alarms etc. There are more than 10 menus for setting the parameters of charging. Device is placed in red plasticified steel box. Main switch, start (scroll) and stop (select) buttons, switch R/S (Ready/Set), led diodes, LCD display for indication and connector for communication with PC computer and indication lamps are placed on the devices front panel. Charge cables, power supply cable and holders for cables, automatic mono-phase fuse in output circuit and main fuse are on the back panel of device.
With software GCDTS v1.01 it is possible to connect device with PC computer via RS232 serial port. Software gives opportunity of showing charge and discharge graphs in real time, possibility of reading charge and discharge data in case that device wasn’t connected with PC, printing and storing the results, creating reports etc.
Gaus Battery Charger GBC165V10A has following protections:
- No sparks during connecting or disconnecting plugs from battery in charge operation;
- Forced and temperature controlled air cooling;
- Control of a minimum of allowed connected battery voltage (forbidden start for voltages less than 10V);
- Temperature protection on heat-sink of semiconductor energy components;
- In case of main power failure, after its restoring, charging automatically continues with earlier set parameters;
- Slow fuse T16A 32 mm in AC circuit;
- Automatic slow fuse 16A in DC circuit;
- Soft start of PWM modulator;
- Soft start in charging input electrolytic capacitance;
- Short circuit protection (if detected current is more than 15A charger is automatically turned off);
- Over voltage protection (>180V);
- Protection from plugs (cables) falling during charge (freezing device until solving of problem);
- Reverse polarity protection with forbidden start.
- Type of voltage converter: mono-phase half-bridge high frequency DC-DC converter;
For charging lead-acid batteries, industrial and stationary, hermetic, GEL...
- Supply 230V +/- 10%, 50Hz 2kW; output power 1650W;
- Nominal input current: 11A; maximal start current: 13A
- Instruments: LCD display 2x16 characters, ampermeter 0-99.9A, voltmeter 0-999.9V, temp1 -99ºC do 99ºC
- Cables with Pb plugs: l=2m, S=6mm2
- Ambient temperature: 5 do +40ºC
||0-10A Cn/10, settable: 1-10A, step 0.1A
||Lead-Acid 12V, No batteries: 1-10 in serial connection; Cn from 10Ah to 100Ah, Sb-Sb, Sb-Ca, Ca-Ca, AGM, Gel
||IU standard, options IUa+ equalizing, IU, IU-Ia+ equalizing, I-U1-U2
|Charge voltage range
||10-165V (permitted by software)
||Settable: 2.20-2.75V/Cell step 0.1V 13,2V-16.5V/battery multiplies with No. batteries Default: 2.4V/Cell, 2.47V, 2.57, 2.67V/Cell, 14.4V, 14.82V, 15.42V, 16.02V*No batt.
||From 1 to 10 batteries in serial connection, Cn=10Ah-100Ah
||Better than 3%
||100mA and 200mV
|Output voltage pulsation
||MOSFET transistors, ultra fast diodes
||Temperature controlled Forced air
||Constant voltage charger with current limit
||Current, voltage, capacity Ah, time
|LCD display during charge
||Status, current, voltage, duration, Ah, warnings, alarms�
||LCD display with 2x16 characters
||Main switch, start and stop buttons, switch Ready/Set, LED diodes
||Steel red plasticified box RAL 3000
GBC165V10A complies with the following requirements:
Options:Final version with charging parameters for specified battery, automatic start/stop operations, without menus for setting parameters...
- EN60335-1/194 (Safety of household and similar electrical appliances-Part 1: General requirements); SIST EN 60335-1, May 1998; JUS IEC 60335-1 1998. and
- EN60335-2-29 (Part 2: Particular requirements for battery chargers); JUS IEC 60335-2-29 year 2000.